热模组测试


氦检机,全自动风量及压力量测仪,模组测试机 -六站式,热管测试机 -六站式,可程式盐雾试验箱,双臂跌落试验机,恒温恒湿试验箱,三坐标测量仪,水平垂直燃烧试验仪,泡棉压缩电阻测试仪,影像精密测量仪,测厚仪

BK-100 氦检机                          
BK-100 Helium Leak Detector

 

仪器功能/Instrument Function
适用于液冷板、管路、散热器等需要密封的产品进行泄露检测。
It is suitable for leak detection of liquid cooling plates, pipelines, radiators and other products that need to be sealed.

测试原理/Testing principle
氦质谱检漏法是利用氦质谱检漏仪的氦分压力测量原理,实现被检件的氦泄漏量测量。当被检件密封面上存在漏孔时,示漏气体氦气及其他成分的气体均会从漏孔泄出,泄露出来的气体进入氦质谱检漏仪后,由于氦质谱检漏仪的选择性识别能力,仅给出气体中的氦气分压力信号值。在获得氦气信号值的基础上,通过标准漏孔比对的方法就可以获得漏孔对氦泄漏量。.
Helium mass spectrometry leak detection method is to realize the measurement of the helium leakage of the tested parts by using the principle of helium partial pressure measurement of the helium mass spectrometry leak detector. When there is a leak on the sealing surface of the tested part, the leaky gas, helium and other gases will leak out of the leak. The leaked gas enters a helium mass spectrometer leak detector. Because of the selective recognition ability of helium mass spectrometer leak detector, only the signal value of helium partial pressure in the gas is given. Based on the helium signal value, the leakage amount of helium can be obtained by the standard leak hole comparison method.

测试能力/Testing Ability
真空模式最小可检漏率:5×10 -13 Pa•m 3 /s / Vacuum mode minimum leak detection rate: 5× 10-13 Pa•m 3 /s
吸枪模式最小可检漏率:5×10 -9 Pa•m 3 /s  / The minimum leak detection rate of suction gun mode: 5× 10-9 Pa•m 3 /s
启动时间:≤3min / Start time: ≤3min
响应时间:≤1s /Response time: ≤1s 
检漏口的最高压力:1500Pa / Maximum pressure of leak detection: 1500Pa
电源要求:220v,50Hz,单相,10A / Power requirements: 220V, 50Hz, single-phase, 10A
工作环境:5-40℃ / Working environment: 5-40℃
相对湿度:≤80% / Relative humidity: ≤80%
长宽高:550x420x900mm / Three high:550x420x900mm
重量:70Kg / Weight:70Kg
功率:900VA / Power:900VA

 


BK-100 全自动风量及压力量测仪                          
BK-100 Automatic Air Volume and Pressure Measuring Instrument

 

仪器功能/Instrument Function
适用于做风扇的PQ特性测试,系统阻抗测试。以及做散热模组RQ测试。
Suitable for fan PQ characteristic test, system wind resistance test. And do the cooling module RQ test.

测试原理/Testing principle
全自动风量及压力量测仪在测试风扇PQ曲线时,可实时记录风扇的压力、流量、转速、电压、电流信息。并且自动生成PQ曲线。
全自动风量及压力量测仪在测试系统阻抗时,可实时记录流量和压力。并且自动生成PQ曲线。
全自动风量及压力量测仪可提供指定风量和指定发热功率的发热源,在限定区域内,将空气吹向被测物体,记录下风量、发热功率以及被测物体温度。即可得到模组散热性能RQ。
Automatic air volume and pressure force measuring instrument in testing fan PQ curve, can real-time record the fan pressure, flow, speed, voltage, current information. And automatically generate PQ curve.
Automatic air volume and pressure meter can record the flow rate and pressure in real time when measuring the system impedance. And automatically generate PQ curve.
Automatic air volume and pressure force measuring instrument can provide the specified air volume and specified heating power of the heating source, in a limited area, the air will be blown to the measured object, record the air volume, heating power and the temperature of the measured object. The module heat dissipation performance Rq can be obtained.

测试能力/Testing Ability
流量测量范围:2.4CFM-250CFM / Flow measurement range: 2.4CFM-250CFM
静压测量范围:0-254mmAq / Static pressure measurement range: 0-254MMAQ
温度测量范围:0-50℃,精度±0.5℃/ Temperature measurement range: 0-50℃, accuracy ±0.5℃
电压测量范围:0-60V,精度±0.5% / Voltage measurement range: 0-60V, accuracy ±0.5%
电流测量范围:0-3A,精度±0.5% / Current measurement range: 0-3A, accuracy ±0.5%
转速测量范围:100-99999rpm,精度±1% / Speed measurement range: 100-99999rpm, accuracy ±1%
腔体横截面积尺寸:0.85(W)x3.6(L)x1.8(H)m / Cavity cross-sectional area size: 0.85 (W) x3.6 (L) x1.8 (H) m
最大风扇直径:280mm / Maximum fan diameter: 280mm
静态最大负载:30Kg / Static maximum load: 30Kg
最大输出功率:600W / Maximum output power: 600W

 


MZ-6Z-1J 模组测试机 -六站式                         
MZ-6Z-1J Modular Test Machine - Six Station Type

 

仪器功能/Instrument Function
适用于模组散热器,对热性能的测试,来满足其散热标准及需求。 
It is suitable for testing the thermal performance of modular radiators to meet their heat dissipation standards and requirements.

测试原理/Testing principle
利用直流电源供应器输出功率,配合模拟 CPU 加热块与模组加热端形状对应的治具块紧密结合,待测模组放入治具并以气缸来进行固定,冷却端以配套治具配合冷却风扇进行冷却,透过热电偶量测各点温度,自动计算出 Rth 及温差, 并自动判断 OK/NG,各数据自动保存.
By using the output power of the DC power supply, the heating block of the analog CPU is closely combined with the fixture block corresponding to the shape of the module's heating end. The module to be tested is put into the fixture and fixed by the cylinder. The cooling end is cooled by the matching fixture and cooling fan.And automatic judgment OK/NG, each data automatically saved .

测试能力/Testing Ability
额定电压:  AC220V  /  Rated voltage: AC220V
额定功率: 1~5KW / Rated power :1~5KW
设备气压: 3~7 kg/cm2  / Pneumatic equipment :3~7 kg/cm2
气缸压力: 10~50KG / Cylinder pressure:10~50KG
测试温度精度:<1℃ / Accuracy of test temperature :<1℃ 
操作温度:0-50℃ / Operating temperature :0-50℃
站台数:六站 /  Number of platforms: six
每站最大加热功率:720W / Maximum heating power per station: 720W 
机台主体尺寸:1800mmX980mmX1220mm / Machine body size: 1800mmX980mmX1220mm

 

 

RG-6Z-1J1S 热管测试机 -六站式                         
RG-6Z-1J1S Heat Pipe Tester - Six Station Type

 

仪器功能/Instrument Function
适用于热管,对热性能的测试,来满足其散热标准及需求。 
Applicable to the heat pipe, the test of thermal performance, to meet its heat dissipation standards and requirements.

测试原理/Testing principle
利用直流电源供应器输出功率,配合模拟 CPU 加热块与产品加热端形狀对应的治具块紧密结合,待测产品放入治具並以气缸來进行固定,冷卻端以冷水机配合产品冷卻端进行冷卻,透过热电偶量測各点溫度,自动計算出 Rth 及溫差, 並自动判断 OK/NG,各数据自动保存,自动上传伺服器.
UUsing the output power of the DC power supply, the heating block of the analog CPU is closely combined with the fixture block corresponding to the shape of the heating end of the product. The product to be tested is put into the fixture and fixed by the cylinder. The cooling end is cooled by the chiller and the cooling end of the product.And automatic judgment OK/NG, the data automatically saved, automatically uploaded to the server .

测试能力/Testing Ability
额定电压:  AC220V  /  Rated voltage: AC220V
额定功率: 1~5KW / Rated power :1~5KW
设备气压: 3~7 kg/cm2  / Pneumatic equipment :3~7 kg/cm2
气缸压力: 1~3KG / Cylinder pressure:1~3KG
测试温度精度:<1℃ / Accuracy of test temperature :<1℃ 
操作温度:0-50℃ / Operating temperature :0-50℃
冷却供液温度:0-50℃ / Cooling liquid supply temperature :0-50℃
供应流量:0-4L/min / Supply flow :0-4L/min
站台数:六站 /  Number of platforms : six
每站最大加热功率:192W / Maximum heating power per station : 192W 
每站最大加热电压:32V / Maximum heating voltage per station : 32V
每站加热电流:6A / Heating current per station : 6A
机台主体尺寸:2000mmX1000mmX700mm / Machine body size: 2000mmX1000mmX700mm

 


BK-160 可程式盐雾试验箱                           
BK-160 Programmable Salt Spray Test Chamber


仪器功能/Instrument Function
本标准规定为各项金属底材于电镀后、有机或无机涂装后等各项表面处理用之盐水喷雾耐触性试验方法。
This standard specifies the salt spray contact resistance test method for various metal substrates after electroplating, organic or inorganic coating and other surface treatments.

测试原理/Testing Principle
本试验方法是使用盐水喷雾试验机将氯化纳溶液,以雾状喷于电镀被覆膜上之一种腐蚀试验方法。
满足CNS3627、3885、4159、7669、8886、JIS D-0201、H-8502、H-8610、K-5400、Z-2371、ISO 3768、3769、3770、ASTM B-117、B-268、GB-T2423、GJB 150.
This test method is a corrosion test method in which sodium chloride solution is sprayed on the electroplating coating film in a mist form using a salt spray test machine.
Meet CNS3627, 3885, 4159, 7669, 8886, JIS D-0201, H-8502, H-8610, K-5400, Z-2371, ISO 3768, 3769, 3770, ASTM B-117, B-268, GB- T2423, GJB 150.

测试能力/Testing Ability
测试温度:35℃ ± 1℃ 波动度:≤±0.5℃ 均匀度: ≤2℃ ./Test temperature: 35°C ± 1°C Fluctuation: ≤±0.5°C Uniformity: ≤2°C
电  源:单相220V. /Electricity source: single-phase 220V
试验室容积(L):800./Laboratory volume (L): 800
内尺寸mm(W×D×H):1600×1000×500. /Inner size mm (W×D×H): 1600×1000×500
外尺寸mm(W×D×H):2300×1350×1485./External dimensions mm (W×D×H): 2300×1350×1485

 

 

BK-315S 双臂跌落试验机
BK-315S Double-arm Drop Test Machine   

 

仪器功能/Instrument Function
主要满足运输条件下产品包装承受的能力,从而改进、完善包装设计. 
It mainly meets the bearing capacity of product packaging under transportation conditions, so as to improve and perfect the packaging design.

测试原理/Testing Principle
采用双柱道向、弹簧缓冲、高度标尺指示,工作稳定可靠,可实现棱、面、角跌落,满足GB/T4857.5-92、ISO2248-1972(E)之标准.
It adopts double-column direction, spring buffer, and height scale indication, stable and reliable work, can realize edge, face, and corner drop, meeting the standards of GB/T4857.5-92, ISO2248-1972 (E).

测试能力/Testing Ability
跌落高度(mm):400-1500 /Drop height (mm): 400-1500
试件最大重量(kg):约80 /Maximum weight of test piece (kg): about 80
试件最大尺寸(mm):1000×800×1000
冲击面板尺寸(mm):1400×1200
底板尺寸:1400*1200*10MM /Maximum size of test piece (mm): 1000×800×1000
试验台外形尺寸(mm):1400×1200×2200 /External dimensions of the test bench (mm): 1400×1200×2200                    
马力:调高1/3P,手动调宽 /Horsepower: increase 1/3P, manual width adjustment                 
电源:380V、1.5KW/Power supply: 380V, 1.5KW
仪器净重(kg):300 /Net weight of the instrument (kg): 300
  

 

BK-1000L  恒温恒湿试验箱                          
BK-1000L Constant Temperature And HumidityTest Chamber

 

仪器功能/Instrument Function
验证检测材料在各种环境下性能的设备及试验各种材料耐热、耐寒,使产品或者材料能达到客户的需求.性能指标符合GB5170、2、3、5、6-95《电工电子産品环境试验设备基本参数检定方法低温、高温、恒定湿热、交变湿热试验设备》的要求
Equipment to verify and test the performance of materials in various environments and test various materials for heat and cold resistance, so that the product or material can meet the needs of customers. Performance indicators comply with GB5170, 2, 3, 5, 6-95 "Electrical and Electronic Products Environment The basic parameter verification method of the test equipment is required for the test equipment of low temperature, high temperature, constant damp heat, alternating damp heat

测试原理/Testing Principle
平恒调温调湿控制系统,以PID方式控制SSR,使系统之加热加湿量等于热湿损耗量.由干湿球测温信号经A/D转换输入控制器CPU与RAN对比输出到I/0板, I/0板发出指令,使送风系统及冷冻系统工作,同时PID控制SSR或是加热SSR工作,或是加湿SSR工作,使热湿量经送风系统均匀测试箱以从而达到平恒调温调温
Pingheng temperature and humidity control system controls the SSR by PID, so that the heating and humidification of the system is equal to the heat and moisture loss. The temperature measurement signal of the dry and wet bulb is compared with the input controller CPU and RAN and output to I/0 through A/D conversion. Board, I/0 board issues instructions to make the air supply system and the refrigeration system work, and at the same time PID controls the SSR or heating SSR work, or humidification SSR work, so that the heat and humidity can be uniformly tested by the air supply system to achieve a constant adjustment. Thermoregulation

测试能力/Test Ability
型号:BK-1000L /Model: BK-1000L
内箱尺寸:W1000*H1000*D1000mm /Inner box size: W1000*H1000*D1000mm
外箱尺寸:W1550*H1950*D1550mm /Carton size: W1550*H1950*D1550mm
温度范围:-70℃ ~ 150℃ /Temperature range: -70℃ ~ 150℃
升温时间:由常温升至150℃约40分钟(空载非线性)/Heating time: about 40 minutes from room temperature to 150℃ (non-linear at no load)
降温时间:由常温降至-70℃约75分钟(空载非线性)/Cooling time: about 75 minutes from room temperature to -70℃ (no-load nonlinearity)
湿度范围:20%~98%R.H./Humidity range: 20%~98%R.H.
电源:单相电 9.5KW 380V 50HZ /Power supply: single-phase power 9.5KW 380V 50HZ

 


CRYSTA-Apex S7106三坐标测量仪
CRYSTA-Apex S7106 Three-Coordinate Measuring Instrument
          

 

仪器功能/Instrument function
本仪器广泛用于机械、模具、电子、电器、汽车零部件、塑料、橡胶、钟表、齿轮、PCB线路板、菲林等行业的半成品及成品的尺寸检测,可编程、可将温度补偿功能系统(选件)安装在本三坐标测量机上。
This instrument is widely used in the size detection of semi-finished and finished products in machinery, molds, electronics, electrical appliances, auto parts, plastics, rubber, watches, gears, PCB circuit boards, film and other industries. It is programmable and can be temperature compensated. Option) is installed on this coordinate measuring machine.

测试原理/Testing Principle
本仪器在16-26ºC温度条件下三坐标测量机主机的精度。该系统具有,通过安装在本仪器各轴光栅尺上的温度传感器和用于工件的温度传感器监测温度,并把测量结果换算成20ºC时的数值并输出的功能。该方式需要在20ºC以外温度环境时测量空间不变形的前提下进行。按照装配温度补偿系统进行设计的,明显优于现有机型的光栅尺温度补偿的简易补偿系统。
Accuracy of the main machine of the coordinate measuring machine under the temperature condition of 16-26ºC. The system has the function of monitoring the temperature through the temperature sensor installed on the scale of each axis of the instrument and the temperature sensor for the workpiece, and converting the measurement result into a value at 20ºC and outputting it. This method needs to be performed under the premise that the measurement space is not deformed in a temperature environment other than 20ºC. Designed in accordance with the assembly temperature compensation system, it is significantly better than the simple compensation system for temperature compensation of the grating ruler of the existing models.

测试能力/Testing Ability
电源要求:220V 50HZ / Power requirements: 220V 50HZ
外形尺寸(mm):2730*1470*1950 / Dimensions (mm):2730*1470*1950
重   量:1951kg / Weight:1951kg
工作台面(mm)  :610*480 / Work surface (mm): 610*480
测量范围(mm) : X-700mm、Y-1000mm / Z-600mm/Measuring range (mm): X-700mm, Y-1000mm, Z-600mm
测量工作台材质:花岗岩 /Measuring table material: granite
载物面尺寸:880*1720mm /Loading surface size: 880*1720mm
工件固定方法:M8*1.25/Workpiece fixing method: M8*1.25
工作最大高度:800mm/Maximum working height: 800mm
工作最大质量:1000kg /Maximum working mass: 1000kg

 


PZ1701A水平垂直燃烧试验仪
PZ1701A Horizontal And Vertical Combustion Testing Machine           

 

仪器功能/Instrument Function
PZ1701A水平垂直燃烧试验仪主要测试和评估电子、电工材料的可燃性能,并对材料的可燃性进行定级评定V-0、V-1、V-2、HB、5V级。
The PZ1701A horizontal and vertical combustion tester mainly tests and evaluates the flammability of electronic and electrical materials, and conducts a graded assessment of the flammability of the materials at V-0, V-1, V-2, HB, 5V levels.

测试原理/Testing Principle
PZ1701A水平垂直燃烧试验仪主要参照UL94、IEC60695-11-4、IEC60695-11-3、GB4943、GB/T5169系列等标准设计,采用规定尺寸的本生灯和特定燃气源(甲烷或丙烷),按一定的火焰高度和一定的施焰角度对呈水平或垂直状态的试品定时施然若干次,已试品点燃、灼热燃烧的持续时间和燃烧长度等来评定其可燃性及着火危险性。
PZ1701A horizontal and vertical combustion tester is mainly designed with reference to UL94, IEC60695-11-4, IEC60695-11-3, GB4943, GB/T5169 series and other standards. It uses a Bunsen burner of specified size and a specific gas source (methane or propane). A certain flame height and a certain flame angle are applied several times to the test sample in a horizontal or vertical state. The igniting, burning duration and burning length of the test sample are used to evaluate its flammability and fire hazard.

测试能力/Testing Ability
火焰高度20±2mm到180±10mm,施焰时间0-999.9±0.1s可调,余焰时间0-999.9s±0.1s,自动记录,线控暂停。
Flame height is 20±2mm to 180±10mm, the flame application time is adjustable from 0-999.9±0.1s, the afterflame time is 0-999.9s±0.1s, automatic recording, remote control pause.
燃烧气体:98%甲烷气或98%丙烷气(一般情况下课采用液化气石油气代替)。
Combustion gas: 98% methane gas or 98% propane gas (in general, liquefied petroleum gas is used instead of petroleum gas).
流量压力:带双流量表及压力表(燃气及空气)。
Flow pressure: with dual flow meters and pressure gauges (gas and air).
温度测试范围:0-1000°火焰温度要求,从100℃±5℃升到700℃±3℃的时间在44±2S及54s±2s之内。
Temperature test range: 0-1000° flame temperature requirement, the time to rise from 100°C±5°C to 700°C±3°C is within 44s±2S and 54s±2s.

 


ST-D500T泡棉压缩电阻测试仪
ST-D500T Foam Compression Resistance Tester  
 
                    

仪器功能/Instrument Function
本仪器专业用于测试导电产品及导电泡棉压缩回弹电阻测试.
This instrument is professionally used to test conductive products and conductive foam compression rebound resistance test.

测试原理/Testing Principle
行程保护:设为上、下限位保护开头,防止超过预设行程./Travel protection: set the upper and lower limit protection at the beginning to prevent exceeding the preset travel.
力量保护:系统可设定力值、防止超过传感器标定值./Power protection: The system can set the force value to prevent exceeding the sensor calibration value.

测试能力/Testing Ability
传感器类型:S型高精密10kg传感器/Sensor type: S type high precision 10kg sensor
电阻测试范围:0-30K Ω/Resistance test range: 0-30K Ω
压缩极限:压缩极限0.1mm/Compression limit: compression limit 0.1mm
压缩夹具:铜块(表面镀金处理)/Compression fixture: copper block (surface gold plating treatment)
力量单位:N、KN、gf、kgf、lbf、kp、tf(SI)、tf(long)等./Power units: N, KN, gf, kgf, lbf, kp, tf (SI), tf (long), etc.
长度单位:mm、cm、inch、m、km、um等./Length unit: mm, cm, inch, m, km, um, etc.
应力单位:Pa 、Kpa、 Mpa、 Gpa、 KN/m² 、N/m² 等./Stress unit: Pa, Kpa, Mpa, Gpa, KN/m², N/m², etc
测量精度:±0.5%./Measurement accuracy: ±0.5%
采集频率:50次/秒/Acquisition frequency: 50 times/sec
机台功率:400W/Machine power: 400W
机台尺寸(mm):500(W)*430 (D)*1260 (H)/Machine size (mm): 500 (W)*430 (D)*1260 (H)
使用电源:220V 50Hz/Power supply: 220V 50Hz

 

 

SVS4030影像精密测量仪         
SVS4030 Image Precision Measuring Instrument    
 

 

仪器功能/Instrument function
本仪器广泛用于机械、模具、电子、电器、汽车零部件、塑料、橡胶、钟表、齿轮、PCB线路板、菲林等行业的半成品及成品的尺寸检测,提高产品尺寸的准确性。
This instrument is widely used in the size detection of semi-finished products and finished products in machinery, molds, electronics, electrical appliances, auto parts, plastics, rubber, watches, gears, PCB circuit boards, film and other industries to improve the accuracy of product sizes.

测试原理/Testing Principle
本仪器有三层工作台设计,精密级V型导轨,保证拥有极高的机械精度。高品质光学系统和高分辨率CCD,确保拥有高品质的测量画面,八区LED环形表面冷光源及轮廓光源,避免工件发热产生变形,多角度多区灯,保证让工件在不同角度有不同效果,精密光学尺,分辨率为0.001mm。
This instrument has a three-layer workbench design and a precision V-shaped guideway to ensure extremely high mechanical accuracy. High-quality optical system and high-resolution CCD to ensure high-quality measurement images. Eight-zone LED ring-shaped surface cold light source and contour light source to avoid deformation of the workpiece due to heat. Multi-angle and multi-zone lights ensure that the workpiece has different effects at different angles. , Precision optical ruler with a resolution of 0.001mm.

测试能力/Testing Ability
电源要求:220V±10%(AC) 50HZ / Power requirements: 220V±10%(AC) 50HZ
外形尺寸(mm):1020*720*1000 / Dimensions (mm): 1020*720*1000
重   量:390kg / Weight: 390kg
工作台面(mm)  :610*480 / Work surface (mm): 610*480
玻璃台面(mm)  :460*360 / Glass table (mm): 460*360
测量范围(mm) : X-400mm、Y-300mm / Z-160mm/Measuring range (mm): X-400mm, Y-300mm, Z-160mm
照    明: LED表面光及下光源,亮度可调 / Illumination: LED surface light and lower light source, adjustable brightness

 


XUL-220 测厚仪
XUL-220 Thickness Gauge   

 

仪器功能/Instrument function
本仪器应用于广泛的X射线荧光镀层测厚及材料分析仪,常用于无损测量细小工件上镀层厚度及材料分析,在小部件如螺钉、螺帽及螺栓的测量、在连接器和电气元器件上的测量以及电镀液的溶液分析测量.
This instrument is used in a wide range of X-ray fluorescence coating thickness measurement and material analyzers. It is often used for non-destructive measurement of coating thickness and material analysis on small workpieces, in the measurement of small parts such as screws, nuts and bolts, in connectors and electrical components On the measurement and the solution analysis measurement of the electroplating solution.

测试原理/Testing Principle
本仪器配备手动XY轴工作台,用于细小样品的精确定位,为了样品定位简单快捷,X射线发生器和比例接收器都集成在仪器下部舱室中,因而样品的底部是实际被测量面,样品则由一层透明的薄膜拖放在测量室中,完全能满足DINISO3497标准ASTM B 568标准.
This instrument is equipped with a manual XY-axis worktable for precise positioning of small samples. In order to facilitate sample positioning, the X-ray generator and proportional receiver are integrated in the lower chamber of the instrument, so the bottom of the sample is the actual surface to be measured. A layer of transparent film is dragged and placed in the measurement room, which can fully meet the DINISO3497 standard and ASTM B568 standard.

测试能力/Testing Ability
电源要求:交流220V 50HZ /Power requirements: AC 220V 50HZ
外部尺寸(宽*深*高)403*588*444mm /External dimensions (width * depth * height) 403*588*444mm
重量:45kg /Weight: 45kg
使用温度:10℃-40℃ /Operating temperature: 10℃-40℃
存储或运输时温度:0℃-50℃ /Temperature during storage or transportation: 0℃-50℃
相对湿度:≤95% 无结露 /Relative humidity: ≤95% without condensation
样品放置区域:310*320mm /Sample placement area: 310*320mm
X/Y轴工作台移动范围:30*40mm /X/Y axis table movement range: 30*40mm
样品最大重量:2kg /Maximum sample weight: 2kg
样品高度:174mm /Sample height: 174mm