Thermal Module Test


Helium Leak Detector, Automatic Air Volume and Pressure Measuring Instrument, Modular Test Machine - Six Station Type, Heat Pipe Tester - Six Station Type, Programmable Salt Spray Test Chamber, Double-arm Drop Test Machine, Constant Temperature And HumidityTest Chamber, Three-Coordinate Measuring Instrument, Horizontal And Vertical Combustion Testing Machine, Foam Compression Resistance Tester, mage Precision Measuring Instrument, Thickness Gauge

BK-100 Helium Leak Detector


Instrument Function
It is suitable for leak detection of liquid cooling plates, pipelines, radiators and other products that need to be sealed.

Testing principle
Helium mass spectrometry leak detection method is to realize the measurement of the helium leakage of the tested parts by using the principle of helium partial pressure measurement of the helium mass spectrometry leak detector. When there is a leak on the sealing surface of the tested part, the leaky gas, helium and other gases will leak out of the leak. The leaked gas enters a helium mass spectrometer leak detector. Because of the selective recognition ability of helium mass spectrometer leak detector, only the signal value of helium partial pressure in the gas is given. Based on the helium signal value, the leakage amount of helium can be obtained by the standard leak hole comparison method.

Testing Ability
Vacuum mode minimum leak detection rate: 5× 10-13 Pa•m 3 /s
The minimum leak detection rate of suction gun mode: 5× 10-9 Pa•m 3 /s
Start time: ≤3min
Response time: ≤1s 
Maximum pressure of leak detection: 1500Pa
Power requirements: 220V, 50Hz, single-phase, 10A
Working environment: 5-40℃
Relative humidity: ≤80%
Three high:550x420x900mm
Weight:70Kg
Power:900VA

 


BK-100 Automatic Air Volume and Pressure Measuring Instrument

Instrument Function
Suitable for fan PQ characteristic test, system wind resistance test. And do the cooling module RQ test.

Testing principle
Automatic air volume and pressure force measuring instrument in testing fan PQ curve, can real-time record the fan pressure, flow, speed, voltage, current information. And automatically generate PQ curve.
Automatic air volume and pressure meter can record the flow rate and pressure in real time when measuring the system impedance. And automatically generate PQ curve.
Automatic air volume and pressure force measuring instrument can provide the specified air volume and specified heating power of the heating source, in a limited area, the air will be blown to the measured object, record the air volume, heating power and the temperature of the measured object. The module heat dissipation performance Rq can be obtained.

Testing Ability
Flow measurement range: 2.4CFM-250CFM
Static pressure measurement range: 0-254MMAQ
Temperature measurement range: 0-50℃, accuracy ±0.5℃
Voltage measurement range: 0-60V, accuracy ±0.5%
Current measurement range: 0-3A, accuracy ±0.5%
Speed measurement range: 100-99999rpm, accuracy ±1%
Cavity cross-sectional area size: 0.85 (W) x3.6 (L) x1.8 (H) m
Maximum fan diameter: 280mm
Static maximum load: 30Kg
Maximum output power: 600W

 


MZ-6Z-1J Modular Test Machine - Six Station Type

 

Instrument Function
It is suitable for testing the thermal performance of modular radiators to meet their heat dissipation standards and requirements.

Testing principle
By using the output power of the DC power supply, the heating block of the analog CPU is closely combined with the fixture block corresponding to the shape of the module's heating end. The module to be tested is put into the fixture and fixed by the cylinder. The cooling end is cooled by the matching fixture and cooling fan.And automatic judgment OK/NG, each data automatically saved .

Testing Ability
Rated voltage: AC220V
Rated power :1~5KW
Pneumatic equipment :3~7 kg/cm2
Cylinder pressure:10~50KG
Accuracy of test temperature :<1℃ 
Operating temperature :0-50℃
Number of platforms: six
Maximum heating power per station: 720W 
Machine body size: 1800mmX980mmX1220mm

 

 

RG-6Z-1J1S Heat Pipe Tester - Six Station Type

 

Instrument Function
Applicable to the heat pipe, the test of thermal performance, to meet its heat dissipation standards and requirements.

Testing principle
UUsing the output power of the DC power supply, the heating block of the analog CPU is closely combined with the fixture block corresponding to the shape of the heating end of the product. The product to be tested is put into the fixture and fixed by the cylinder. The cooling end is cooled by the chiller and the cooling end of the product.And automatic judgment OK/NG, the data automatically saved, automatically uploaded to the server .

Testing Ability
Rated voltage: AC220V
Rated power :1~5KW
Pneumatic equipment :3~7 kg/cm2
Cylinder pressure:1~3KG
Accuracy of test temperature :<1℃ 
Operating temperature :0-50℃
Cooling liquid supply temperature :0-50℃
Supply flow :0-4L/min
Number of platforms : six
Maximum heating power per station : 192W 
Maximum heating voltage per station : 32V
Heating current per station : 6A
Machine body size: 2000mmX1000mmX700mm

 


BK-160 Programmable Salt Spray Test Chamber


Instrument Function
This standard specifies the salt spray contact resistance test method for various metal substrates after electroplating, organic or inorganic coating and other surface treatments.

Testing Principle
This test method is a corrosion test method in which sodium chloride solution is sprayed on the electroplating coating film in a mist form using a salt spray test machine.
Meet CNS3627, 3885, 4159, 7669, 8886, JIS D-0201, H-8502, H-8610, K-5400, Z-2371, ISO 3768, 3769, 3770, ASTM B-117, B-268, GB- T2423, GJB 150.

Testing Ability
Test temperature: 35°C ± 1°C Fluctuation: ≤±0.5°C Uniformity: ≤2°C
Electricity source: single-phase 220V
Laboratory volume (L): 800
Inner size mm (W×D×H): 1600×1000×500
External dimensions mm (W×D×H): 2300×1350×1485

 

 

BK-315S Double-arm Drop Test Machine   

 

Instrument Function
It mainly meets the bearing capacity of product packaging under transportation conditions, so as to improve and perfect the packaging design.

Testing Principle
It adopts double-column direction, spring buffer, and height scale indication, stable and reliable work, can realize edge, face, and corner drop, meeting the standards of GB/T4857.5-92, ISO2248-1972 (E).

Testing Ability
Drop height (mm): 400-1500
Maximum weight of test piece (kg): about 80
Maximum size of test piece (mm): 1000×800×1000
External dimensions of the test bench (mm): 1400×1200×2200                    
Horsepower: increase 1/3P, manual width adjustment                 
Power supply: 380V, 1.5KW
Net weight of the instrument (kg): 300


  

BK-1000L Constant Temperature And HumidityTest Chamber

 

Instrument Function
Equipment to verify and test the performance of materials in various environments and test various materials for heat and cold resistance, so that the product or material can meet the needs of customers. Performance indicators comply with GB5170, 2, 3, 5, 6-95 "Electrical and Electronic Products Environment The basic parameter verification method of the test equipment is required for the test equipment of low temperature, high temperature, constant damp heat, alternating damp heat

Testing Principle
Pingheng temperature and humidity control system controls the SSR by PID, so that the heating and humidification of the system is equal to the heat and moisture loss. The temperature measurement signal of the dry and wet bulb is compared with the input controller CPU and RAN and output to I/0 through A/D conversion. Board, I/0 board issues instructions to make the air supply system and the refrigeration system work, and at the same time PID controls the SSR or heating SSR work, or humidification SSR work, so that the heat and humidity can be uniformly tested by the air supply system to achieve a constant adjustment. Thermoregulation

Test Ability
Model: BK-1000L
Inner box size: W1000*H1000*D1000mm
Carton size: W1550*H1950*D1550mm
Temperature range: -70℃ ~ 150℃
Heating time: about 40 minutes from room temperature to 150℃ (non-linear at no load)
Cooling time: about 75 minutes from room temperature to -70℃ (no-load nonlinearity)
Humidity range: 20%~98%R.H.
Power supply: single-phase power 9.5KW 380V 50HZ

 


CRYSTA-Apex S7106 Three-Coordinate Measuring Instrument           

 

Instrument function
This instrument is widely used in the size detection of semi-finished and finished products in machinery, molds, electronics, electrical appliances, auto parts, plastics, rubber, watches, gears, PCB circuit boards, film and other industries. It is programmable and can be temperature compensated. Option) is installed on this coordinate measuring machine.

Testing Principle
Accuracy of the main machine of the coordinate measuring machine under the temperature condition of 16-26ºC. The system has the function of monitoring the temperature through the temperature sensor installed on the scale of each axis of the instrument and the temperature sensor for the workpiece, and converting the measurement result into a value at 20ºC and outputting it. This method needs to be performed under the premise that the measurement space is not deformed in a temperature environment other than 20ºC. Designed in accordance with the assembly temperature compensation system, it is significantly better than the simple compensation system for temperature compensation of the grating ruler of the existing models.

Testing Ability
Power requirements: 220V 50HZ
Dimensions (mm):2730*1470*1950
Weight:1951kg
Work surface (mm): 610*480
Measuring range (mm): X-700mm, Y-1000mm, Z-600mm
Measuring table material: granite
Loading surface size: 880*1720mm
Workpiece fixing method: M8*1.25
Maximum working height: 800mm
Maximum working mass: 1000kg

 


PZ1701A Horizontal And Vertical Combustion Testing Machine           

Instrument Function
The PZ1701A horizontal and vertical combustion tester mainly tests and evaluates the flammability of electronic and electrical materials, and conducts a graded assessment of the flammability of the materials at V-0, V-1, V-2, HB, 5V levels.

Testing Principle
PZ1701A horizontal and vertical combustion tester is mainly designed with reference to UL94, IEC60695-11-4, IEC60695-11-3, GB4943, GB/T5169 series and other standards. It uses a Bunsen burner of specified size and a specific gas source (methane or propane). A certain flame height and a certain flame angle are applied several times to the test sample in a horizontal or vertical state. The igniting, burning duration and burning length of the test sample are used to evaluate its flammability and fire hazard.

Testing Ability
Flame height is 20±2mm to 180±10mm, the flame application time is adjustable from 0-999.9±0.1s, the afterflame time is 0-999.9s±0.1s, automatic recording, remote control pause.
Combustion gas: 98% methane gas or 98% propane gas (in general, liquefied petroleum gas is used instead of petroleum gas).
Flow pressure: with dual flow meters and pressure gauges (gas and air).
Temperature test range: 0-1000° flame temperature requirement, the time to rise from 100°C±5°C to 700°C±3°C is within 44s±2S and 54s±2s.

 


ST-D500T Foam Compression Resistance Tester   
                    

Instrument Function
This instrument is professionally used to test conductive products and conductive foam compression rebound resistance test.

Testing Principle
Travel protection: set the upper and lower limit protection at the beginning to prevent exceeding the preset travel.
Power protection: The system can set the force value to prevent exceeding the sensor calibration value.

Testing Ability
Sensor type: S type high precision 10kg sensor
Resistance test range: 0-30K Ω
Compression limit: compression limit 0.1mm
Compression fixture: copper block (surface gold plating treatment)
Power units: N, KN, gf, kgf, lbf, kp, tf (SI), tf (long), etc.
Length unit: mm, cm, inch, m, km, um, etc.
Stress unit: Pa, Kpa, Mpa, Gpa, KN/m², N/m², etc
Measurement accuracy: ±0.5%
Acquisition frequency: 50 times/sec
Machine power: 400W
Machine size (mm): 500 (W)*430 (D)*1260 (H)
Power supply: 220V 50Hz

 

 

SVS4030 Image Precision Measuring Instrument      

 

Instrument function
This instrument is widely used in the size detection of semi-finished products and finished products in machinery, molds, electronics, electrical appliances, auto parts, plastics, rubber, watches, gears, PCB circuit boards, film and other industries to improve the accuracy of product sizes.

Testing Principle
This instrument has a three-layer workbench design and a precision V-shaped guideway to ensure extremely high mechanical accuracy. High-quality optical system and high-resolution CCD to ensure high-quality measurement images. Eight-zone LED ring-shaped surface cold light source and contour light source to avoid deformation of the workpiece due to heat. Multi-angle and multi-zone lights ensure that the workpiece has different effects at different angles. , Precision optical ruler with a resolution of 0.001mm.

Testing Ability
Power requirements: 220V±10%(AC) 50HZ
Dimensions (mm): 1020*720*1000
Weight: 390kg
Work surface (mm): 610*480
Glass table (mm): 460*360
Z-160mm/Measuring range (mm): X-400mm, Y-300mm, Z-160mm
Illumination: LED surface light and lower light source, adjustable brightness

 


XUL-220 Thickness Gauge   

 

Instrument function
This instrument is used in a wide range of X-ray fluorescence coating thickness measurement and material analyzers. It is often used for non-destructive measurement of coating thickness and material analysis on small workpieces, in the measurement of small parts such as screws, nuts and bolts, in connectors and electrical components On the measurement and the solution analysis measurement of the electroplating solution.

Testing Principle
This instrument is equipped with a manual XY-axis worktable for precise positioning of small samples. In order to facilitate sample positioning, the X-ray generator and proportional receiver are integrated in the lower chamber of the instrument, so the bottom of the sample is the actual surface to be measured. A layer of transparent film is dragged and placed in the measurement room, which can fully meet the DINISO3497 standard and ASTM B568 standard.

Testing Ability
Power requirements: AC 220V 50HZ
External dimensions (width * depth * height) 403*588*444mm
Weight: 45kg
Operating temperature: 10℃-40℃
Temperature during storage or transportation: 0℃-50℃
Relative humidity: ≤95% without condensation
Sample placement area: 310*320mm
X/Y axis table movement range: 30*40mm
Maximum sample weight: 2kg
Sample height: 174mm