Form in place gasket


Brief Introduction

With programmable automated robot, EMI gaskets can be dispensed onto metal, or conductive painted, plated, or metallic surfaces in the electronic enclosures. Form in place gasket (FIP) is suitable for applications that requires environmental sealiental elements.FIPprovides the lowest total cost for small cross section and complex pattern applications. A range of conductive fillers can be selected to meet critical design requirement.

 

FC@PROPERTIES FC@UNIT FC@TEST METHOD CG-9010 CG-9011 CG-9012 CG-5010     CG-5011 CG-5020 CG-8021R CG-8025R CG-8020 CG-8021 CG-8028 CG-7010 CG-7010AD SG-701 SG-701M
Benefit - - High performance Surface-Q Aerospace class High elasticity Superfine Low Temperature Curing Super soft Superfine High velocity Super soft Low stress Corrosion resistance Corrosion resistance Super soft Adhesive type
Conductive Materials - - Ag/Cu Ag/Cu Ag/Cu Ag/Ni Ag/Ni Ag/Ni Ni/C Ni/C Ni/C Ni/C Ni/C Ag/Al Ag/Al - -
Base Material - - Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone Silicone
Curing Conditions - - Room temperature curing Room temperature curing Room temperature curing Room temperature curing Room temperature curing High temperature curing Room temperature curing Room temperature curing High temperature curing High temperature curing High temperature curing Room temperature curing Room temperature curing Room temperature curing Room temperature curing
Curing Temperature - 25 25 25 25 25 100 25 25 150 150 100 25 25 25 25
Curing Time - - 24h 12h 24h 24h 24h 4h 24h 24h 30min 30min 1h 12h 12h 12h 4h
Hardness Shore A ASTM D2240 60 55 55 50 60 55 45 45 60 45 35 60 60 20 35
Tensile Strength PSI ASTM D412 130 130 130 200 200 150 150 120 150 150 110 130 130 650 650
Elongation % ASTM D412 150 150 150 100 180 100 100 100 100 100 100 180 180 300 300
Density g/cm³ ASTM D792 3.2 3.0 3.2 3.8 3.8 3.9 1.9 2.2 1.9 1.9 1.9 2.2 2.2 1.2 1.2
Volume Resistivity ohm-cm MIL-DTL-83528C 0.003 0.004 0.003 0.005 0.01 0.01 0.04 0.04 0.03 0.04 0.03 0.008 0.008 - -
Compression Rate @ 100 ℃ for 70 hours % ASTM D395-B 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
Working Temperature - -55~+125 -55~+125 -55~+125 -55~+125 -55~+125 -55~+150 -55~+125 -55~+125 -55~+125 -55~+125 -55~+125 -55~+120 -55~+125 -55~+125 -55~+125
Flame Retardant Grade (Between aluminum plates) - UL 94 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0
Shielding Effectiveness (AVG 200mhz-18ghz) dB MIL-DTL-83528C >100 >90 >100 >90 >90 >90 >80 >80 >80 >80 >80 >90 >100 - -
Adhesive Point Size W1.1*H0.9*L10mm N/cm Nystein QA-WI-054 12 12 12 16 13 15 12 15 25 17 15 13 14 20 20
Dispensing Size @30% compression, W1.1*H0.9*L10mm N/cm Nystein QA-WI-058 39 40 28 25 19 28 21 14 43 20 12 32 35 13 15

Minimum Recommended Value /

Maximum Recommended Value of Dispensing Size

mm Width * Height

0.6*0.4/

2.5*1.7

0.5*0.25/

2.5*1.7

0.6*0.4/

2.5*1.7

0.5*0.25/

2.5*1.7

0.3*0.3/

2.5*1.7

0.5*0.4/

2.5*1.7

0.6*0.4/

1.65*1.96

0.4*0.3/

2.5*1.7

0.7*0.5/

2.5*1.7

0.7*0.5/

2.5*1.7

0.7*0.5/

2.5*1.7

0.6*0.4/

2.5*1.7

0.6*0.4/

2.5*1.7

0.6*0.4/

2.5*1.7

0.6*0.4/

2.5*1.7

Storage Time Month - 3 3 3 3 3 6 3 3 6 6 6 3 3 3 3
Storage Conditions - -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10 -30~-10